👷🏻‍♀️Intro to Civil Engineering Unit 6 – Soil Mechanics & Foundations

What's Soil Mechanics All About?

• Soil mechanics studies the behavior and properties of soils as an engineering material
• Focuses on the interaction between soil particles, water, and air within the soil matrix
• Investigates how soils respond to various loading conditions (static loads, dynamic loads, earthquakes)
• Explores the stability of soil masses and their potential for failure (slope stability, landslides, soil liquefaction)
• Examines the compressibility and consolidation of soils under applied loads
• Analyzes the shear strength of soils, which is crucial for designing foundations and earth retaining structures
• Considers the permeability and seepage of water through soils, affecting groundwater flow and drainage

Key Soil Properties You Need to Know

• Grain size distribution describes the relative proportions of different particle sizes in a soil sample
  • Classified into gravel (>2mm), sand (0.075-2mm), silt (0.002-0.075mm), and clay (<0.002mm)
• Plasticity refers to a soil's ability to undergo deformation without cracking or crumbling
  • Measured by Atterberg limits (liquid limit, plastic limit, plasticity index)
• Porosity is the ratio of void space to the total volume of a soil sample
  • Affects soil compressibility, permeability, and water retention
• Permeability measures a soil's ability to allow fluid flow through its pores
  • Depends on factors like grain size, void ratio, and soil structure
• Shear strength represents a soil's resistance to shearing stresses
  • Influenced by cohesion (c) and angle of internal friction ($\phi$)
• Compressibility describes a soil's tendency to decrease in volume under applied loads
  • Related to the soil's void ratio and stress history
• Specific gravity is the ratio of the density of soil solids to the density of water
  • Used in various calculations and soil classification

How Water Affects Soil Behavior

• Water content (w) is the ratio of the mass of water to the mass of solid particles in a soil sample
  • Influences soil consistency, strength, and compressibility
• Saturation occurs when all the void spaces in a soil are filled with water
  • Affects soil behavior under loading and drainage conditions
• Capillary action causes water to rise above the water table in fine-grained soils
  • Can lead to swelling, shrinkage, and changes in soil strength
• Pore water pressure (u) is the pressure exerted by water within soil pores
  • Influences effective stress ($\sigma'$) and soil shear strength
• Seepage refers to the flow of water through soil pores
  • Can cause soil erosion, piping, and instability in earth structures
• Consolidation is the gradual reduction in soil volume due to the dissipation of excess pore water pressure
  • Occurs in saturated, fine-grained soils under sustained loading
• Frost action can cause soil heaving and damage to structures in cold climates
  • Results from the formation of ice lenses in soil pores

Stress and Strain in Soils

• Total stress ($\sigma$) is the sum of effective stress ($\sigma'$) and pore water pressure (u)
  • $\sigma = \sigma' + u$
• Effective stress ($\sigma'$) is the stress carried by the soil skeleton
  • Controls soil deformation and strength
• Vertical stress ($\sigma_v$) is the stress acting perpendicular to a horizontal plane
  • Increases with depth due to the weight of overlying soil
• Horizontal stress ($\sigma_h$) is the stress acting parallel to a horizontal plane
  • Often expressed as a fraction of vertical stress ($K_0 = \sigma_h / \sigma_v$)
• Shear stress ($\tau$) is the stress acting parallel to a plane
  • Causes soil particles to slide or roll relative to each other
• Normal strain ($\varepsilon$) is the change in length per unit length in the direction of the applied stress
  • $\varepsilon = \Delta L / L$
• Shear strain ($\gamma$) is the angular distortion caused by shear stress
  • $\gamma = \Delta x / h$
• Elastic moduli (Young's modulus E, shear modulus G) relate stress to strain in the elastic range
  • Useful for predicting soil deformation under working loads

Soil Classification Systems

• Unified Soil Classification System (USCS) is widely used in geotechnical engineering
  • Based on grain size distribution and plasticity characteristics
  • Divides soils into coarse-grained (gravels G, sands S) and fine-grained (silts M, clays C) categories
  • Further classified by gradation (well-graded W, poorly-graded P) and plasticity (low L, high H)
• AASHTO Soil Classification System is commonly used in highway engineering
  • Groups soils into seven main categories (A-1 through A-7) based on grain size and plasticity
  • Considers soil suitability for road subgrades and embankments
• Other classification systems include the British Soil Classification System (BSCS) and the International Soil Classification System (ISCS)
  • Adapted to specific regional or national requirements
• Soil classification helps engineers predict soil behavior and select appropriate design parameters
  • Provides a common language for describing soils across projects and disciplines

Foundations 101: Types and Purposes

• Shallow foundations transfer loads to the near-surface soil layers
  • Examples include spread footings, strip footings, and mat foundations
• Deep foundations transfer loads to deeper, more competent soil or rock layers
  • Examples include piles, drilled shafts, and caissons
• Spread footings are isolated, square, or rectangular concrete pads that support individual columns or posts
  • Suitable for moderate loads and favorable soil conditions
• Strip footings are continuous, elongated concrete members that support load-bearing walls
  • Distribute loads linearly and provide stability against lateral forces
• Mat foundations are large, continuous slabs that cover the entire footprint of a structure
  • Used when soil conditions are poor or loads are heavy
• Piles are long, slender elements driven or drilled into the ground
  • Transfer loads through friction (skin resistance) and end bearing
• Drilled shafts are cast-in-place concrete elements installed by drilling and filling with reinforced concrete
  • Provide high load capacity and resistance to lateral loads
• Caissons are large, hollow, pre-cast concrete elements sunk into the ground
  • Often used for bridge piers and underwater structures

Site Investigation and Soil Testing

• Desk study involves gathering and reviewing existing information about the site
  • Includes geological maps, aerial photographs, and previous site reports
• Site reconnaissance is a visual inspection of the site and surrounding area
  • Identifies surface features, topography, and potential geotechnical hazards
• Subsurface exploration techniques are used to obtain soil samples and in-situ test data
  • Examples include boreholes, test pits, and cone penetration tests (CPT)
• Laboratory tests are performed on soil samples to determine their physical and mechanical properties
  • Includes grain size analysis, Atterberg limits, shear strength tests, and consolidation tests
• In-situ tests are conducted in the field to evaluate soil properties and behavior
  • Examples include standard penetration test (SPT), vane shear test, and pressuremeter test
• Geophysical methods use non-invasive techniques to map subsurface conditions
  • Includes seismic refraction, ground-penetrating radar (GPR), and electrical resistivity
• Interpretation of site investigation data is crucial for developing a reliable ground model
  • Considers spatial variability, anomalies, and potential geotechnical risks

Practical Applications in Civil Engineering

• Foundation design involves selecting the appropriate type, size, and depth of foundation based on soil conditions and structural requirements
  • Considers bearing capacity, settlement, and lateral stability
• Retaining wall design requires an understanding of soil pressures and stability
  • Examples include gravity walls, cantilever walls, and mechanically stabilized earth (MSE) walls
• Slope stability analysis assesses the potential for slope failures and landslides
  • Involves calculating factors of safety and designing stabilization measures
• Pavement design considers the subgrade soil properties and expected traffic loads
  • Includes flexible (asphalt) and rigid (concrete) pavement systems
• Soil improvement techniques are used to enhance soil properties and performance
  • Examples include compaction, grouting, and installation of geosynthetics
• Excavation support systems are designed to ensure the stability of temporary excavations
  • Includes soldier pile and lagging, sheet pile walls, and diaphragm walls
• Geotechnical earthquake engineering evaluates the response of soils and foundations to seismic loading
  • Considers liquefaction potential, site amplification, and soil-structure interaction